Hello,

Voila j'ai actuellement deux partitions : l'une avec Windows Vista Ultimate et l'autre avec Ubuntu Feisty Fawn ainsi qu'un disque dur externe de 75go en NTFS. J'ai donc tenté de branché mon DD Externe sous Ubuntu mais un message d'erreur apparait " Impossible de monter ce volume ".

Vis à vis du tuto de M@teo21, j'aurais aimer que mon DD Externe soit la partition contenant mes docs, donc je doit convertir cette partition en ext3.

J'aimerais donc savoir si FS Driver, le logiciel permettant de rendre ext3 compatible Windows fonctionne sous Vista ( desolé j'ai perdu mes points d'interrogation ).
Inversement, j'ai aussi installer les paquets " ntfs-config", d'après le Labo Linux de chez Supinfo, ces paquets sont censé me permettre d'écrire et de lire des données NTFS sous Linux. Dois je donc laisser mon disque dur externe en NTFS ( pt d'interrogation )

Et ma dernière question : comment faire pour accéder à mon disque dur externe sous Ubuntu ( pt d'interrogation ).

Je vous remercie d'avance !

Up

Up sil vous plait !

bonjour

une petite précision concernant la partition "documents" du tuto de mateo (la partition /home, en fait) : cette partition contiendra non seulement les documents (si on le souhaite), mais elle contiendra aussi (et surtout) tous les fichiers de configuration propres au système. Placer /home sur une partition ntfs, meme avec les drivers pour écrire dessus, me parait donc une tres tres mauvaise idée. Cette partition est vitale pour le fonctionnement de linux, donc il faut la placer sur un système de fichier linux (ici, ext3). Je suis meme sceptique sur le fait de la placer sur un disque externe (quitte apres à utiliser ce disque externe pour stocker tes "vrais" documents).

Sinon, concernant le fonctionnement de tel ou tel logiciel sous Vista, je ne peux pas te répondre : windows (et en particulier Vista) me devient de plus en plus étranger vu que je suis à 100% sous linux.

Enfin, pour la reconnaissance de ton disque externe par ubuntu : ben je suis pas un spécialiste.
Le message apparait au moment meme où tu branches ton disque, ou apres avoir essayé de faire quelque chose avec ?
Que donne la commande "dmesg" juste apres avoir branché le disque ?

a+

C'est à dire que sur mon disque dur externe j'ai tout mes divx et mes musiques, tout ce que je " réclame " c'est de pouvoir lire et écrire sur ce disque dur externe ces fichiers. A votre avis, que faut t'il que je fasse.

J'ai entendu parlé d'un outil appelé NTFS-3g qui permetterait de faire pas mal de chose sur NTFS via Linux

Sinon pour mon disque dur, voici le détail du message d'erreur quand je branche l'appareil :



Et la réponse à la commande dmesg :

Citation : Mon Terminale

[ 0.000000] copy_e820_map() start: 000000003ffde000 size: 0000000000022000 end: 0000000040000000 type: 4
[ 0.000000] copy_e820_map() start: 00000000ff780000 size: 0000000000880000 end: 0000000100000000 type: 2
[ 0.000000] BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
[ 0.000000] BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
[ 0.000000] BIOS-e820: 00000000000e4000 - 0000000000100000 (reserved)
[ 0.000000] BIOS-e820: 0000000000100000 - 000000003ffd0000 (usable)
[ 0.000000] BIOS-e820: 000000003ffd0000 - 000000003ffde000 (ACPI data)
[ 0.000000] BIOS-e820: 000000003ffde000 - 0000000040000000 (ACPI NVS)
[ 0.000000] BIOS-e820: 00000000ff780000 - 0000000100000000 (reserved)
[ 0.000000] 127MB HIGHMEM available.
[ 0.000000] 896MB LOWMEM available.
[ 0.000000] found SMP MP-table at 000ff780
[ 0.000000] Entering add_active_range(0, 0, 262096) 0 entries of 256 used
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0 -> 4096
[ 0.000000] Normal 4096 -> 229376
[ 0.000000] HighMem 229376 -> 262096
[ 0.000000] early_node_map[1] active PFN ranges
[ 0.000000] 0: 0 -> 262096
[ 0.000000] On node 0 totalpages: 262096
[ 0.000000] DMA zone: 32 pages used for memmap
[ 0.000000] DMA zone: 0 pages reserved
[ 0.000000] DMA zone: 4064 pages, LIFO batch:0
[ 0.000000] Normal zone: 1760 pages used for memmap
[ 0.000000] Normal zone: 223520 pages, LIFO batch:31
[ 0.000000] HighMem zone: 255 pages used for memmap
[ 0.000000] HighMem zone: 32465 pages, LIFO batch:7
[ 0.000000] DMI 2.3 present.
[ 0.000000] ACPI: RSDP (v000 ACPIAM ) @ 0x000f90c0
[ 0.000000] ACPI: RSDT (v001 A M I OEMRSDT 0x07000520 MSFT 0x00000097) @ 0x3ffd0000
[ 0.000000] ACPI: FADT (v002 A M I OEMFACP 0x07000520 MSFT 0x00000097) @ 0x3ffd0200
[ 0.000000] ACPI: MADT (v001 A M I OEMAPIC 0x07000520 MSFT 0x00000097) @ 0x3ffd0390
[ 0.000000] ACPI: MCFG (v001 A M I OEMMCFG 0x07000520 MSFT 0x00000097) @ 0x3ffd03f0
[ 0.000000] ACPI: SSDT (v001 ATI ATIPATCH 0x00000001 INTL 0x02002026) @ 0x3ffd3db0
[ 0.000000] ACPI: OEMB (v001 A M I AMI_OEM 0x07000520 MSFT 0x00000097) @ 0x3ffde040
[ 0.000000] ACPI: DSDT (v001 0AAAA 0AAAA000 0x00000000 INTL 0x02002026) @ 0x00000000
[ 0.000000] ATI board detected. Disabling timer routing over 8254.
[ 0.000000] ACPI: PM-Timer IO Port: 0x808
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
[ 0.000000] Processor #0 15:3 APIC version 16
[ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
[ 0.000000] Processor #1 15:3 APIC version 16
[ 0.000000] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 2, version 33, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 21 low level)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ2 used by override.
[ 0.000000] Enabling APIC mode: Flat. Using 1 I/O APICs
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] Allocating PCI resources starting at 50000000 (gap: 40000000:bf780000)
[ 0.000000] Detected 1989.895 MHz processor.
[ 41.882061] Built 1 zonelists. Total pages: 260049
[ 41.882064] Kernel command line: root=UUID=7d6a37a3-e8e4-46ca-8f77-751f0b4f3140 ro quiet splash locale=fr_FR
[ 41.882198] mapped APIC to ffffd000 (fee00000)
[ 41.882201] mapped IOAPIC to ffffc000 (fec00000)
[ 41.882204] Enabling fast FPU save and restore... done.
[ 41.882207] Enabling unmasked SIMD FPU exception support... done.
[ 41.882215] Initializing CPU#0
[ 41.882282] PID hash table entries: 4096 (order: 12, 16384 bytes)
[ 41.883843] Console: colour VGA+ 80x25
[ 41.884340] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[ 41.884810] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 41.906756] Memory: 1028196k/1048384k available (1992k kernel code, 19492k reserved, 900k data, 328k init, 130880k highmem)
[ 41.906765] virtual kernel memory layout:
[ 41.906766] fixmap : 0xfff4e000 - 0xfffff000 ( 708 kB)
[ 41.906768] pkmap : 0xff800000 - 0xffc00000 (4096 kB)
[ 41.906769] vmalloc : 0xf8800000 - 0xff7fe000 ( 111 MB)
[ 41.906770] lowmem : 0xc0000000 - 0xf8000000 ( 896 MB)
[ 41.906771] .init : 0xc03d9000 - 0xc042b000 ( 328 kB)
[ 41.906773] .data : 0xc02f2374 - 0xc03d36d4 ( 900 kB)
[ 41.906774] .text : 0xc0100000 - 0xc02f2374 (1992 kB)
[ 41.906777] Checking if this processor honours the WP bit even in supervisor mode... Ok.
[ 41.986170] Calibrating delay using timer specific routine.. 3983.75 BogoMIPS (lpj=7967502)
[ 41.986211] Security Framework v1.0.0 initialized
[ 41.986219] SELinux: Disabled at boot.
[ 41.986233] Mount-cache hash table entries: 512
[ 41.986376] CPU: After generic identify, caps: 178bfbff e3d3fbff 00000000 00000000 00000001 00000000 00000003
[ 41.986384] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
[ 41.986386] CPU: L2 Cache: 512K (64 bytes/line)
[ 41.986389] CPU 0(2) -> Core 0
[ 41.986391] CPU: After all inits, caps: 178bfbff e3d3fbff 00000000 00000410 00000001 00000000 00000003
[ 41.986402] Compat vDSO mapped to ffffe000.
[ 41.986407] Remapping vsyscall page to ffffe000
[ 41.986417] Checking 'hlt' instruction... OK.
[ 42.002302] SMP alternatives: switching to UP code
[ 42.002747] Early unpacking initramfs... done
[ 42.284494] ACPI: Core revision 20060707
[ 42.284976] ACPI: Looking for DSDT in initramfs... file /DSDT.aml not found, using machine DSDT.
[ 42.287003] CPU0: AMD Athlon(tm) 64 X2 Dual Core Processor 3800+ stepping 02
[ 42.287026] SMP alternatives: switching to SMP code
[ 42.287170] Booting processor 1/1 eip 3000
[ 42.295186] Initializing CPU#1
[ 42.375554] Calibrating delay using timer specific routine.. 3979.89 BogoMIPS (lpj=7959781)
[ 42.375562] CPU: After generic identify, caps: 178bfbff e3d3fbff 00000000 00000000 00000001 00000000 00000003
[ 42.375568] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
[ 42.375570] CPU: L2 Cache: 512K (64 bytes/line)
[ 42.375573] CPU 1(2) -> Core 1
[ 42.375574] CPU: After all inits, caps: 178bfbff e3d3fbff 00000000 00000410 00000001 00000000 00000003
[ 42.377863] CPU1: AMD Athlon(tm) 64 X2 Dual Core Processor 3800+ stepping 02
[ 42.377879] Total of 2 processors activated (7963.64 BogoMIPS).
[ 42.378045] ENABLING IO-APIC IRQs
[ 42.378237] ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 42.417918] ..MP-BIOS bug: 8254 timer not connected to IO-APIC
[ 42.417969] ...trying to set up timer (IRQ0) through the 8259A ... failed.
[ 42.417971] ...trying to set up timer as Virtual Wire IRQ... works.
[ 42.565509] checking TSC synchronization across 2 CPUs:
[ 0.000001] CPU#0 had 1082 usecs TSC skew, fixed it up.
[ 0.000003] CPU#1 had -1082 usecs TSC skew, fixed it up.
[ 0.003994] Brought up 2 CPUs
[ 0.113720] migration_cost=413
[ 0.113965] Booting paravirtualized kernel on bare hardware
[ 0.114053] Time: 21:45:46 Date: 08/04/107
[ 0.114084] NET: Registered protocol family 16
[ 0.114164] EISA bus registered
[ 0.114167] ACPI: bus type pci registered
[ 0.114952] PCI: PCI BIOS revision 3.00 entry at 0xf0031, last bus=2
[ 0.114954] PCI: Using configuration type 1
[ 0.114956] Setting up standard PCI resources
[ 2.329688] ACPI: Interpreter enabled
[ 2.329691] ACPI: Using IOAPIC for interrupt routing
[ 2.330120] ACPI: PCI Root Bridge [PCI0] (0000:00)
[ 2.330125] PCI: Probing PCI hardware (bus 00)
[ 2.331186] Boot video device is 0000:01:00.0
[ 2.331586] PCI: Transparent bridge - 0000:00:14.4
[ 2.331620] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 2.342489] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCE2._PRT]
[ 2.347611] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P9._PRT]
[ 2.350032] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 7 10 11 12 14 15) *0, disabled.
[ 2.350285] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 7 10 11 12 14 15) *0, disabled.
[ 2.350535] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 7 10 11 12 14 15) *0, disabled.
[ 2.350784] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 7 10 11 12 14 15) *0, disabled.
[ 2.351037] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 7 10 11 12 14 15) *0, disabled.
[ 2.351289] ACPI: PCI Interrupt Link [LNKF] (IRQs 9) *0, disabled.
[ 2.351540] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 7 10 11 12 14 15) *0, disabled.
[ 2.351793] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 7 10 11 12 14 15) *0, disabled.
[ 2.351890] Linux Plug and Play Support v0.97 (c) Adam Belay
[ 2.351899] pnp: PnP ACPI init
[ 2.356682] pnp: PnP ACPI: found 14 devices
[ 2.356686] PnPBIOS: Disabled by ACPI PNP
[ 2.356738] PCI: Using ACPI for IRQ routing
[ 2.356741] PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
[ 2.366665] NET: Registered protocol family 8
[ 2.366667] NET: Registered protocol family 20
[ 2.367397] pnp: 00:0a: ioport range 0xe00-0xe7f has been reserved
[ 2.367625] PCI: Bridge: 0000:00:02.0
[ 2.367628] IO window: 7000-7fff
[ 2.367631] MEM window: fa700000-fe7fffff
[ 2.367633] PREFETCH window: bff00000-dfefffff
[ 2.367637] PCI: Bridge: 0000:00:14.4
[ 2.367640] IO window: 8000-8fff
[ 2.367646] MEM window: fe800000-fe8fffff
[ 2.367651] PREFETCH window: 50000000-500fffff
[ 2.367667] PCI: Setting latency timer of device 0000:00:02.0 to 64
[ 2.367709] NET: Registered protocol family 2
[ 2.405194] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 2.405387] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
[ 2.406502] TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
[ 2.407108] TCP: Hash tables configured (established 131072 bind 65536)
[ 2.407111] TCP reno registered
[ 2.421230] checking if image is initramfs... it is
[ 2.979259] Freeing initrd memory: 6771k freed
[ 3.524000] audit: initializing netlink socket (disabled)
[ 3.524000] audit(1188942348.708:1): initialized
[ 3.524000] highmem bounce pool size: 64 pages
[ 3.524000] VFS: Disk quotas dquot_6.5.1
[ 3.524000] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 3.524000] io scheduler noop registered
[ 3.524000] io scheduler anticipatory registered
[ 3.524000] io scheduler deadline registered
[ 3.524000] io scheduler cfq registered (default)
[ 3.568000] PCI: Setting latency timer of device 0000:00:02.0 to 64
[ 3.568000] assign_interrupt_mode Found MSI capability
[ 3.568000] Allocate Port Service[0000:00:02.0:pcie00]
[ 3.568000] isapnp: Scanning for PnP cards...
[ 3.920000] isapnp: No Plug & Play device found
[ 3.944000] Real Time Clock Driver v1.12ac
[ 3.944000] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
[ 3.944000] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 3.944000] serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
[ 3.944000] 00:05: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 3.944000] 00:06: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
[ 3.944000] mice: PS/2 mouse device common for all mice
[ 3.944000] RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize
[ 3.944000] input: Macintosh mouse button emulation as /class/input/input0
[ 3.944000] Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
[ 3.944000] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
[ 3.944000] PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 1
[ 3.944000] PNP: PS/2 controller doesn't have AUX irq; using default 12
[ 3.948000] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 3.948000] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 3.948000] EISA: Probing bus 0 at eisa.0
[ 3.948000] Cannot allocate resource for EISA slot 7
[ 3.948000] Cannot allocate resource for EISA slot 8
[ 3.948000] EISA: Detected 0 cards.
[ 3.976000] input: AT Translated Set 2 keyboard as /class/input/input1
[ 3.976000] TCP cubic registered
[ 3.976000] NET: Registered protocol family 1
[ 3.976000] Starting balanced_irq
[ 3.980000] Using IPI No-Shortcut mode
[ 3.980000] ACPI: (supports S0 S1 S3 S4 S5)
[ 3.980000] Magic number: 7:781:802
[ 3.980000] Freeing unused kernel memory: 328k freed
[ 3.984000] Time: acpi_pm clocksource has been installed.
[ 5.196000] Capability LSM initialized
[ 5.736000] SCSI subsystem initialized
[ 5.740000] libata version 2.20 loaded.
[ 5.740000] sata_sil 0000:00:11.0: version 2.2
[ 5.740000] ACPI: PCI Interrupt 0000:00:11.0[A] -> GSI 23 (level, low) -> IRQ 16
[ 5.740000] ata1: SATA max UDMA/100 cmd 0xf8834c80 ctl 0xf8834c8a bmdma 0xf8834c00 irq 16
[ 5.752000] ata2: SATA max UDMA/100 cmd 0xf8834cc0 ctl 0xf8834cca bmdma 0xf8834c08 irq 16
[ 5.752000] scsi0 : sata_sil
[ 5.756000] 8139too Fast Ethernet driver 0.9.28
[ 5.760000] usbcore: registered new interface driver usbfs
[ 5.760000] usbcore: registered new interface driver hub
[ 5.760000] usbcore: registered new device driver usb
[ 5.760000] ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
[ 5.776000] ieee1394: Initialized config rom entry `ip1394'
[ 6.220000] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 6.232000] ata1.00: ata_hpa_resize 1: sectors = 312581808, hpa_sectors = 312581808
[ 6.232000] ata1.00: ATA-6: ST3160023AS, 3.00, max UDMA/133
[ 6.232000] ata1.00: 312581808 sectors, multi 16: LBA48 NCQ (depth 0/32)
[ 6.244000] ata1.00: ata_hpa_resize 1: sectors = 312581808, hpa_sectors = 312581808
[ 6.244000] ata1.00: configured for UDMA/100
[ 6.244000] scsi1 : sata_sil
[ 6.556000] ata2: SATA link down (SStatus 0 SControl 300)
[ 6.556000] scsi 0:0:0:0: Direct-Access ATA ST3160023AS 3.00 PQ: 0 ANSI: 5
[ 6.560000] ACPI: PCI Interrupt 0000:00:12.0[A] -> GSI 22 (level, low) -> IRQ 17
[ 6.560000] ata3: SATA max UDMA/100 cmd 0xf88ce880 ctl 0xf88ce88a bmdma 0xf88ce800 irq 17
[ 6.560000] ata4: SATA max UDMA/100 cmd 0xf88ce8c0 ctl 0xf88ce8ca bmdma 0xf88ce808 irq 17
[ 6.560000] scsi2 : sata_sil
[ 6.872000] ata3: SATA link down (SStatus 0 SControl 300)
[ 6.872000] scsi3 : sata_sil
[ 7.184000] ata4: SATA link down (SStatus 0 SControl 300)
[ 7.188000] ACPI: PCI Interrupt 0000:02:03.0[A] -> GSI 20 (level, low) -> IRQ 18
[ 7.188000] eth0: RealTek RTL8139 at 0xf882c400, 00:13:d3:8b:1b:7c, IRQ 18
[ 7.188000] eth0: Identified 8139 chip type 'RTL-8100B/8139D'
[ 7.188000] 8139cp: 10/100 PCI Ethernet driver v1.3 (Mar 22, 2004)
[ 7.188000] ACPI: PCI Interrupt 0000:00:13.0[A] -> GSI 19 (level, low) -> IRQ 19
[ 7.188000] ohci_hcd 0000:00:13.0: OHCI Host Controller
[ 7.188000] ohci_hcd 0000:00:13.0: new USB bus registered, assigned bus number 1
[ 7.188000] ohci_hcd 0000:00:13.0: irq 19, io mem 0xfebfe000
[ 7.248000] usb usb1: configuration #1 chosen from 1 choice
[ 7.248000] hub 1-0:1.0: USB hub found
[ 7.248000] hub 1-0:1.0: 4 ports detected
[ 7.352000] ACPI: PCI Interrupt 0000:00:13.1[A] -> GSI 19 (level, low) -> IRQ 19
[ 7.352000] ohci_hcd 0000:00:13.1: OHCI Host Controller
[ 7.352000] ohci_hcd 0000:00:13.1: new USB bus registered, assigned bus number 2
[ 7.352000] ohci_hcd 0000:00:13.1: irq 19, io mem 0xfebfd000
[ 7.412000] usb usb2: configuration #1 chosen from 1 choice
[ 7.412000] hub 2-0:1.0: USB hub found
[ 7.412000] hub 2-0:1.0: 4 ports detected
[ 7.516000] ACPI: PCI Interrupt 0000:02:04.0[A] -> GSI 21 (level, low) -> IRQ 21
[ 7.572000] ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[21] MMIO=[fe8fe800-fe8fefff] Max Packet=[2048] IR/IT contexts=[4/8]
[ 7.576000] ACPI: PCI Interrupt 0000:00:13.2[A] -> GSI 19 (level, low) -> IRQ 19
[ 7.576000] ehci_hcd 0000:00:13.2: EHCI Host Controller
[ 7.576000] ehci_hcd 0000:00:13.2: new USB bus registered, assigned bus number 3
[ 7.576000] ehci_hcd 0000:00:13.2: irq 19, io mem 0xfebfc000
[ 7.576000] ehci_hcd 0000:00:13.2: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[ 7.576000] usb usb3: configuration #1 chosen from 1 choice
[ 7.576000] hub 3-0:1.0: USB hub found
[ 7.576000] hub 3-0:1.0: 8 ports detected
[ 7.680000] ATIIXP: IDE controller at PCI slot 0000:00:14.1
[ 7.680000] ACPI: PCI Interrupt 0000:00:14.1[A] -> GSI 16 (level, low) -> IRQ 20
[ 7.680000] ATIIXP: chipset revision 0
[ 7.680000] ATIIXP: not 100% native mode: will probe irqs later
[ 7.680000] ide0: BM-DMA at 0xff00-0xff07, BIOS settings: hda:pio, hdb:pio
[ 7.680000] ide1: BM-DMA at 0xff08-0xff0f, BIOS settings: hdc:DMA, hdd:pio
[ 7.680000] Probing IDE interface ide0...
[ 8.252000] Probing IDE interface ide1...
[ 8.852000] ieee1394: Host added: ID:BUS[0-00:1023] GUID[0010dc0000bcd776]
[ 8.996000] hdc: _NEC DVD_RW ND-3530A, ATAPI CD/DVD-ROM drive
[ 9.036000] usb 3-4: new high speed USB device using ehci_hcd and address 5
[ 9.172000] usb 3-4: configuration #1 chosen from 1 choice
[ 9.172000] hub 3-4:1.0: USB hub found
[ 9.172000] hub 3-4:1.0: 4 ports detected
[ 9.668000] ide1 at 0x170-0x177,0x376 on irq 15
[ 9.680000] SCSI device sda: 312581808 512-byte hdwr sectors (160042 MB)
[ 9.680000] sda: Write Protect is off
[ 9.680000] sda: Mode Sense: 00 3a 00 00
[ 9.680000] SCSI device sda: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 9.680000] SCSI device sda: 312581808 512-byte hdwr sectors (160042 MB)
[ 9.680000] sda: Write Protect is off
[ 9.680000] sda: Mode Sense: 00 3a 00 00
[ 9.680000] SCSI device sda: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 9.680000] sda:<6>hdc: ATAPI 48X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache, UDMA(33)
[ 9.696000] Uniform CD-ROM driver Revision: 3.20
[ 9.696000] sda1 sda2 < sda5 sda6 >
[ 9.720000] sd 0:0:0:0: Attached scsi disk sda
[ 9.724000] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 9.764000] usb 2-1: new low speed USB device using ohci_hcd and address 2
[ 9.976000] usb 2-1: configuration #1 chosen from 1 choice
[ 10.048000] Attempting manual resume
[ 10.048000] swsusp: Resume From Partition 8:5
[ 10.048000] PM: Checking swsusp image.
[ 10.048000] PM: Resume from disk failed.
[ 10.056000] ReiserFS: sda6: found reiserfs format "3.6" with standard journal
[ 10.056000] ReiserFS: sda6: using ordered data mode
[ 10.056000] ReiserFS: sda6: journal params: device sda6, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
[ 10.056000] ReiserFS: sda6: checking transaction log (sda6)
[ 10.084000] ReiserFS: sda6: Using r5 hash to sort names
[ 10.280000] usb 2-4: new full speed USB device using ohci_hcd and address 3
[ 10.484000] usb 2-4: configuration #1 chosen from 1 choice
[ 10.484000] usbcore: registered new interface driver hiddev
[ 10.788000] usb 1-1: new low speed USB device using ohci_hcd and address 3
[ 10.992000] usb 1-1: configuration #1 chosen from 1 choice
[ 11.300000] usb 1-2: new low speed USB device using ohci_hcd and address 4
[ 11.504000] usb 1-2: configuration #1 chosen from 1 choice
[ 11.512000] input: Microsoft Microsoft Trackball Explorer� as /class/input/input2
[ 11.512000] input: USB HID v1.00 Mouse [Microsoft Microsoft Trackball Explorer�] on usb-0000:00:13.1-1
[ 11.524000] input: UC-LOGIC Tablet WP4030U as /class/input/input3
[ 11.524000] input,hiddev96: USB HID v1.00 Mouse [UC-LOGIC Tablet WP4030U] on usb-0000:00:13.0-1
[ 11.528000] input: Honey Bee Nostromo SpeedPad2 as /class/input/input4
[ 11.528000] input: USB HID v1.10 Keyboard [Honey Bee Nostromo SpeedPad2 ] on usb-0000:00:13.0-2
[ 11.536000] input: Honey Bee Nostromo SpeedPad2 as /class/input/input5
[ 11.536000] input: USB HID v1.10 Mouse [Honey Bee Nostromo SpeedPad2 ] on usb-0000:00:13.0-2
[ 11.536000] usbcore: registered new interface driver usbhid
[ 11.536000] drivers/usb/input/hid-core.c: v2.6:USB HID core driver
[ 11.708000] usb 3-4.1: new high speed USB device using ehci_hcd and address 7
[ 11.812000] usb 3-4.1: configuration #1 chosen from 1 choice
[ 18.480000] eth0: link down
[ 19.736000] NET: Registered protocol family 17
[ 19.836000] Linux agpgart interface v0.102 (c) Dave Jones
[ 19.984000] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 19.984000] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 20.064000] piix4_smbus 0000:00:14.0: Found 0000:00:14.0 device
[ 20.076000] input: PC Speaker as /class/input/input6
[ 20.112000] parport: PnPBIOS parport detected.
[ 20.112000] parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE,EPP]
[ 20.272000] nvidia: module license 'NVIDIA' taints kernel.
[ 20.524000] ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 18 (level, low) -> IRQ 22
[ 20.524000] PCI: Setting latency timer of device 0000:01:00.0 to 64
[ 20.524000] NVRM: loading NVIDIA Linux x86 Kernel Module 1.0-9631 Thu Nov 9 17:38:10 PST 2006
[ 20.588000] usbcore: registered new interface driver libusual
[ 20.628000] Initializing USB Mass Storage driver...
[ 20.628000] scsi4 : SCSI emulation for USB Mass Storage devices
[ 20.636000] usbcore: registered new interface driver usb-storage
[ 20.636000] USB Mass Storage support registered.
[ 20.636000] usb-storage: device found at 3
[ 20.636000] usb-storage: waiting for device to settle before scanning
[ 20.664000] ACPI: PCI Interrupt 0000:02:00.0[A] -> GSI 20 (level, low) -> IRQ 18
[ 20.664000] cmipci: no OPL device at 0x388, skipping...
[ 20.728000] ACPI: PCI Interrupt 0000:00:14.5[B] -> GSI 17 (level, low) -> IRQ 23
[ 20.888000] fuse init (API version 7.8)
[ 20.920000] lp0: using parport0 (interrupt-driven).
[ 20.964000] Adding 1020088k swap on /dev/disk/by-uuid/b9730165-a14a-c9b8-10a6-26478572ac35. Priority:-1 extents:1 across:1020088k
[ 25.636000] usb-storage: device scan complete
[ 25.644000] scsi 4:0:0:0: Direct-Access Generic USB SD Reader 1.00 PQ: 0 ANSI: 0
[ 25.648000] scsi 4:0:0:1: Direct-Access Generic USB CF Reader 1.01 PQ: 0 ANSI: 0
[ 25.656000] scsi 4:0:0:2: Direct-Access Generic USB SM Reader 1.02 PQ: 0 ANSI: 0
[ 25.660000] scsi 4:0:0:3: Direct-Access Generic USB MS Reader 1.03 PQ: 0 ANSI: 0
[ 25.672000] sd 4:0:0:0: Attached scsi removable disk sdb
[ 25.672000] sd 4:0:0:0: Attached scsi generic sg1 type 0
[ 25.680000] sd 4:0:0:1: Attached scsi removable disk sdc
[ 25.680000] sd 4:0:0:1: Attached scsi generic sg2 type 0
[ 25.692000] sd 4:0:0:2: Attached scsi removable disk sdd
[ 25.692000] sd 4:0:0:2: Attached scsi generic sg3 type 0
[ 25.704000] sd 4:0:0:3: Attached scsi removable disk sde
[ 25.704000] sd 4:0:0:3: Attached scsi generic sg4 type 0
[ 36.224000] ndiswrapper version 1.38 loaded (preempt=no,smp=yes)
[ 36.472000] usb 3-4.1: reset high speed USB device using ehci_hcd and address 7
[ 36.600000] ndiswrapper: driver wlanuig (Sagem SA,06/03/2004, 3.0.18.2) loaded
[ 38.004000] wlan0: ethernet device 00:60:b3:bc:b0:da using NDIS driver: wlanuig, version: 0x30012, NDIS version: 0x501, vendor: 'Sagem XG703 USB 802.11g', 0CDE:0008.F.conf
[ 38.004000] wlan0: encryption modes supported: WEP; TKIP with WPA; AES/CCMP with WPA
[ 38.004000] usbcore: registered new interface driver ndiswrapper
[ 41.352000] NET: Registered protocol family 10
[ 41.352000] lo: Disabled Privacy Extensions
[ 41.352000] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 41.716000] Using specific hotkey driver
[ 41.788000] No dock devices found.
[ 41.848000] input: Power Button (FF) as /class/input/input7
[ 41.848000] ACPI: Power Button (FF) [PWRF]
[ 41.848000] input: Power Button (CM) as /class/input/input8
[ 41.848000] ACPI: Power Button (CM) [PWRB]
[ 41.928000] ibm_acpi: ec object not found
[ 42.016000] pcc_acpi: loading...
[ 42.212000] powernow-k8: Found 2 AMD Athlon(tm) 64 X2 Dual Core Processor 3800+ processors (version 2.00.00)
[ 42.212000] powernow-k8: 0 : fid 0xc (2000 MHz), vid 0x8
[ 42.212000] powernow-k8: 1 : fid 0xa (1800 MHz), vid 0xa
[ 42.212000] powernow-k8: 2 : fid 0x2 (1000 MHz), vid 0x12
[ 48.496000] ppdev: user-space parallel port driver
[ 49.168000] apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
[ 49.168000] apm: disabled - APM is not SMP safe.
[ 49.364000] Bluetooth: Core ver 2.11
[ 49.364000] NET: Registered protocol family 31
[ 49.364000] Bluetooth: HCI device and connection manager initialized
[ 49.364000] Bluetooth: HCI socket layer initialized
[ 49.380000] Bluetooth: L2CAP ver 2.8
[ 49.380000] Bluetooth: L2CAP socket layer initialized
[ 49.396000] Bluetooth: RFCOMM socket layer initialized
[ 49.396000] Bluetooth: RFCOMM TTY layer initialized
[ 49.396000] Bluetooth: RFCOMM ver 1.8
[ 52.084000] wlan0: no IPv6 routers present
[ 706.756000] APIC error on CPU0: 00(40)
[ 1281.920000] APIC error on CPU0: 40(40)
[ 2023.640000] usb 3-4.4: new high speed USB device using ehci_hcd and address 8
[ 2026.712000] usb 3-4.4: device descriptor read/64, error -110
[ 2031.116000] usb 3-4.4: configuration #1 chosen from 1 choice
[ 2031.116000] scsi5 : SCSI emulation for USB Mass Storage devices
[ 2031.116000] usb-storage: device found at 8
[ 2031.116000] usb-storage: waiting for device to settle before scanning
[ 2036.116000] usb-storage: device scan complete
[ 2041.688000] usb 3-4.4: reset high speed USB device using ehci_hcd and address 8
[ 2042.928000] scsi 5:0:0:0: Direct-Access Generic USB Disk 9.02 PQ: 0 ANSI: 2
[ 2042.932000] SCSI device sdf: 156301488 512-byte hdwr sectors (80026 MB)
[ 2042.932000] sdf: Write Protect is off
[ 2042.932000] sdf: Mode Sense: 03 00 00 00
[ 2042.932000] sdf: assuming drive cache: write through
[ 2042.932000] SCSI device sdf: 156301488 512-byte hdwr sectors (80026 MB)
[ 2042.932000] sdf: Write Protect is off
[ 2042.932000] sdf: Mode Sense: 03 00 00 00
[ 2042.932000] sdf: assuming drive cache: write through
[ 2042.932000] sdf: sdf1
[ 2042.960000] sd 5:0:0:0: Attached scsi disk sdf
[ 2042.960000] sd 5:0:0:0: Attached scsi generic sg5 type 0
wizard50@Wizard50-Computer:~$

euh, quand le système est suffisament sympa pour t'indiquer ce qu'il pense etre le problème et te propose quelques solutions pour tenter d'y remedier, ce serait quand meme dommage de ne pas suivre ses conseils....

Ou alors tu ne comprends pas un mot d'anglais et il faut qu'on te traduise ?

a+